Raspberry Jam

-

Well, here's the proof that I finally got hold of a RaspberryPi computer (for £25 including p&p).  The odd arrangement of the monitor has its own story of course.  I was given this Hanns-G LCD monitor recently by another kind Freegler, but the power supply was faulty.  What made it worth fixing was the DVI interface which can be directly connected to HDMI and HDMI is what the RaspberryPi outputs. So I took it apart and found that it was basically running off 12v and 5v which was easy enough to test rig from an old mini-PC power unit.  The monitor has a good crisp image and once I tidy the wiring up a bit it will be fine for use with the RaspberryPi.  The HDMI-to-DVI cable was £2.99 out of a local discount shop.  Always worth a look in Poundland, World of Pound, Home Bargains and the other discount shops, you never know what they have.


For the time being, we built a Lego box for the RaspberryPi, pretty much from scratch.  The sticker on the top was to hint at the computer being destined (one day) to be the front end for a vehicle diagnostic system, but that's as far off as it ever was!  It's a lot of fun trying to get there though.

Comments

  1. Anonymous23 July 2012 at 10:54

    Your Pi arrived - I'm dead jealous! CR (@computing_teach). Mine has been in the pipeline for some time...

    ReplyDelete

Post a Comment

Popular posts from this blog

Update on the touch monitor

-
This is tantalising... I found some data on driver chips used on these low-cost monitors and some of them have an I2C connection for sending pixel data directly to the screen. This may be to allow text or graphics overlay. Anyway the chip on my 7" screens is an AR05C-LF and there are millions of these in stock in the far east, but I can't so far find a data sheet for this chip or its sibling the AR05CA-LF. Being able to send digital pixel data via I2C directly to the screen would be, well, brilliant.
Read more

Apple iPad SSH Connection to Linux Laptop

-
Image
I was given this older Apple iPad a while back and was looking into installing Linux on it. Options are limited, but it is possible to install a shell to the iPad and run command line stuff.  SSH is always a bit of fun so I logged into my Linux Mint laptop remotely for a giggle. It was interesting running a few simple commands from the iPad. My cheapo Bluetooth keyboard came in very useful although I discovered that the iPad's OS version predated mouse support so the trackpad didn't work. Going a step further, I got my Raspberry Pi going again and was able to install VNC on the iPad and remotely control the Raspberry Pi's desktop. Could be useful! I'm also looking at fitting a small heatsink and 5-volt fan (recovered from a broken laptop) to the Raspberry Pi and over clocking it to 1GHz.
Read more

Skoda Rapid Heater Re-circulation Motor Repair

-
Image
In the autumn of 2018 the heater re-circulation motor (I'll refer to this as the HRM from now on) in my 2015 Skoda Rapid decided to fail. It had been making a grinding and clicking noise for a while and I had asked the local Skoda dealer to look into this during a routine service, which they didn't, but more on that later. The problem was that the motor failed in the re-circulate setting so the interior of the car steamed up very quickly and the windscreen couldn't be de-misted. Putting the air-conditioning on was a short-term solution up until the outside temperature dropped below 10 Celsius and that stopped working! There isn't a lot of information online about the Rapid because it is a less common model than other Skodas, but it shares a lot of design with the Fabia and Octavia so it wasn't too hard to get diagrams showing where the motor was and how it works. To get at the HRM I had to remove the glove box (7 Torx screws) and the heater motor (5 Torx screws),
Read more